Gnee Steel (tianjin) Co., Ltd
+8615824687445

5052A Aluminum Alloy Sheet: Properties, Tempers and Applications

Apr 13, 2023

What Is 5052A Aluminum Alloy Sheet?

5052A aluminum alloy sheet is a non-heat-treatable aluminium-magnesium (Al-Mg) alloy of the 5xxx series. It is supplied to the same magnesium and chromium ranges as the well-established 5052 grade - nominally 2.2-2.8% Mg and 0.15-0.35% Cr, with aluminium as the balance - but is produced through a leaner processing route. The result is mechanical performance and corrosion behaviour close to 5052 at a lower cost, and this is the reason medium and light-duty applications that traditionally used 5052 sheet are increasingly converted to 5052A.

The alloy is normally ordered in the O (annealed), H32, H34, H36 and H38 strain-hardened tempers as coil, cut-to-length sheet and blanked panels. Reference standards for the sheet product include ASTM B209, EN 485-2 and GB/T 3880, while chemical composition limits are specified in ASTM B209 and EN 573-3.

Typical Mechanical Properties by Temper

The table below gives typical room-temperature tensile properties for 5052A sheet in the common tempers. Elongation values are gauge and temper dependent and should be confirmed against the applicable table of ASTM B209 for the thickness being purchased.

Temper Tensile strength (MPa) Yield strength, 0.2% offset (MPa, min) Typical use
O 170-215 65 Deep drawing, tanks and formed parts
H32 215-255 160 General forming, panels, enclosures
H34 235-275 180 Structural and semi-structural panels
H36 255-295 200 Load-bearing sheet components
H38 270-310 215 High-strength sheet parts

Physical and Fabrication Properties

Density: approximately 2.68 g/cm3, about one third that of steel, which supports weight reduction in transport equipment.

Melting range: approximately 593-649 C.

Thermal conductivity: approximately 138 W/(m.K) at 25 C.

Modulus of elasticity: approximately 70 GPa.

Heat treatment: the alloy cannot be strengthened by heat treatment; strength is developed by strain hardening and controlled by annealing, so temper selection is the main lever on final properties.

Formability: good plasticity in the semi-cold-worked condition and lower plasticity at fully cold-worked tempers; the O and H32 tempers are preferred for deep drawing and severe bending, and bend radii should be increased as hardness rises.

Corrosion resistance: good resistance to atmospheric, fresh-water and seawater exposure, without the stress-corrosion sensitivity associated with many high-strength 7xxx alloys.

Weldability: good by TIG and MIG using 5356 or 4043 filler wire; welded joints retain useful strength in the annealed heat-affected zone.

Machinability and finishing: machinability is comparatively low, as is typical for 5xxx alloys, while polishing, brushing, anodising and painting are all readily performed.

Where 5052A Aluminum Alloy Sheet Is Used

The alloy is specified for low-load components that require high plasticity and reliable weldability while working in contact with liquid or gaseous media. Typical applications include:

Oil and fuel tanks, liquid containers and deep-drawn vessels.

Road tankers, refrigerated trucks, refrigerated containers and other transport bodies.

Marine sheet metal parts, instrumentation, and boat and shipboard fittings exposed to salt spray.

Welded parts for automobiles, aircraft, subway and light-rail vehicles.

Pressure vessels with strict fire-protection requirements.

Refrigeration equipment and drilling equipment.

Street-lamp brackets, rivets, hardware items and electrical enclosures.

Ordering and Inspection Checklist

Item to confirm Recommended specification
Grade and temper 5052A in O, H32, H34, H36 or H38, stated on the purchase order and on the certificate
Thickness and tolerance Nominal gauge with tolerance limits per ASTM B209 or EN 485-4
Width, length, edge condition Mill edge, trimmed edge or slit coil to the required forming width
Mechanical properties Tensile strength, yield strength and elongation reported on the test certificate
Chemical composition Mg, Cr, Fe, Si, Cu, Mn, Zn and Ti reported against ASTM B209 or EN 573-3 limits
Surface and flatness Mill, bright or polished finish; flatness checked on a levelled plate
Documentation Material test certificate in EN 10204 3.1 format, plus dimensional and visual inspection record

Commonly supplied thickness range is 0.5-6.0 mm, with wider programmes available for coil and cut-to-length sheet; buyers should confirm availability of the exact gauge and temper before placing volume orders.

FAQ

Q: Is 5052A aluminum alloy sheet heat treatable?
No. It is a non-heat-treatable Al-Mg alloy. Strength is obtained by strain hardening and adjusted by annealing, so the required mechanical properties are achieved by choosing the correct temper rather than by a post-forming heat treatment.

Q: What is the difference between 5052A and 5052?
5052A uses the same magnesium and chromium ranges as 5052 and delivers comparable strength, corrosion resistance and weldability, but at a lower production cost, so it is used for medium and light-duty parts where the full premium of 5052 is not justified.

Q: Which temper should be used for deep drawing?
The annealed O temper gives the highest ductility and is the usual choice for severe deep drawing, while H32 is a practical compromise where a moderate strength increase is acceptable. Harder tempers such as H36 and H38 should be formed with generous bend radii.

Q: Is 5052A sheet suitable for marine service?
Yes. The alloy has good resistance to seawater and atmospheric exposure and is widely used for ship sheet metal parts, instrumentation and other low-load marine components where a higher-strength marine grade is not required.

Q: Can 5052A sheet be welded?
It welds well by TIG and MIG processes with 5356 or 4043 filler wire. The heat-affected zone softens after welding, so joints should be designed on the annealed properties of the alloy rather than on the parent-metal temper values.

Q: What documentation should accompany a delivery?
A material test certificate in EN 10204 3.1 format reporting the standard, grade, temper, heat number, chemical composition, mechanical properties and dimensions, together with inspection records for thickness, flatness and surface condition.