A PPGI coil price is never a single market number. It is the sum of a substrate cost, a coating cost, a paint-system cost and the commercial terms attached to one specific order. Two quotations that differ on a per-tonne basis are usually describing two different products, so the first job for a buyer is to compare like with like.
How a PPGI Coil Price Is Built Up
Four cost blocks decide the final figure, and each of them can be moved independently by the specification the buyer sends to the mill.
Substrate: hot-dip galvanized, cold-rolled steel coil, normally 0.12-2.0 mm thick and 600-1500 mm wide, priced on the daily strip market.
Zinc coating: coating mass from 30 g/m2 up to 275 g/m2, which sets both corrosion life and a large share of raw-material cost.
Paint system: primer and topcoat chemistry, total film thickness, colour and gloss level.
Commercial terms: quantity, coil weight, coil internal diameter, dimensional tolerances, inspection level and delivery schedule.
| Price driver | Typical range | Effect on cost |
|---|---|---|
| Strip thickness | 0.12-2.0 mm | Thin strip costs more per tonne than heavy strip |
| Zinc coating mass | 30-275 g/m2 | Higher coating mass raises cost and extends corrosion life |
| Paint film | About 20-25 micrometres total | Thicker or higher-grade paint raises cost |
| Coil weight | 3-5 t | Small or non-standard coils add handling cost |
Base Metal and Zinc Coating Thickness
Zinc coating mass is the first place where unusually cheap offers are created. The galvanized substrate under a paint system is commonly supplied with a lighter zinc layer than a bare galvanized coil of the same nominal thickness, because the paint film takes over part of the barrier duty. A colour-coated coil with a 40-60 g/m2 zinc layer is therefore not the same product as a heavy-coated galvanized coil, and the two should never be compared on price alone.
Where the end use involves cut edges in a humid or coastal environment, coating mass should be specified explicitly in grams per square metre on both surfaces, together with the base metal thickness and the tolerance class.
Paint System, Colour and Film Thickness
The paint system is the second large variable. Standard exterior systems use an epoxy or polyester primer with a topcoat of polyester, silicon-modified polyester or a fluorocarbon coating for aggressive exposure. Total dry film thickness is typically around 20-25 micrometres, split between primer and topcoat.
Standard RAL shades are the least expensive because they are produced in long runs.
White and very light shades need more pigment and a thicker topcoat, so they carry a premium.
Special colours, metallic finishes and textured surfaces need separate paint batches and add both cost and lead time.
Back-coat type and gloss level also change the price and must be stated in the enquiry.
Coil Dimensions, Coil Weight and Order Volume
Dimension and handling requirements change the conversion cost. Common supply is 600-1500 mm wide, 0.12-2.0 mm thick, with a coil internal diameter of 508 mm or 610 mm and coil weights from 3 t to 5 t. Non-standard widths need slitting, small coils lose yield on the line, and very tight thickness or camber tolerances slow the line down.
Order volume matters as much as the technical sheet. A single 20 ft container load, roughly 25 t, is the usual minimum for an economical coating run; small trial lots are accepted by many mills but are priced above the tonne rate of a full repeat order.
HS Code, Export Rules and Landed Cost
PPGI coil is classified under HS heading 7210.70, which covers flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, painted, varnished or coated with plastics. National tariff schedules break this heading into further subheadings, so the ten-digit code used for customs entry depends on the importing country and should be confirmed against the current national tariff.
Export-side policy also feeds into the delivered price. Changes to export rebates and duty treatment for coated flat-rolled products have shifted the effective export cost of coated coil since 2021, and freight, exchange rates and container availability then move the landed figure again. A price comparison that ignores these items is incomplete even when the mill ex-works number is correct.
How to Read a Quotation Correctly
A quotation is only meaningful when it states the full specification: base metal grade and thickness, zinc coating mass, paint system and film thickness, colour reference, coil weight, coil internal diameter, quantity, tolerance standard, packing method and validity period. Offers that leave two or three of these items open are usually priced on the cheapest assumption and will be revised upward later.
For the same specification, quotations from established producers normally sit inside a narrow band. When an offer falls well outside that band, the gap is almost always paid for somewhere else: a thinner zinc layer, a lighter paint film, off-spec substrate, delayed shipment or an additional charge added after the order is placed.
Frequently Asked Questions
Q: Can I trust the lowest PPGI coil price on the market?
For an identical specification the spread between credible producers is normally narrow, often within about USD 100 per tonne. Offers far below that band usually mean a lighter zinc coating, a thinner paint film, non-conforming substrate or hidden charges, so verify the specification line by line instead of judging on price alone.
Q: Why can a PPGI coil price be close to, or even below, a bare galvanized coil price?
Because the two products carry different zinc coating masses. The galvanized substrate used under paint is often thinner in coating than a heavy galvanized coil, and the paint system is costed separately. Compare coating mass, paint chemistry and film thickness before drawing any conclusion.
Q: What information is needed to get an accurate quotation quickly?
Thickness, width, coil weight and coil internal diameter, zinc coating mass, paint system and total film thickness, colour reference, quantity and the intended end use. All of these factors influence the price, and special requirements on paint type or painting method should be stated in the same enquiry.
Q: What is the HS code for PPGI steel coil?
It falls under HS heading 7210.70 for flat-rolled iron or non-alloy steel of 600 mm width or more that is painted, varnished or coated with plastics. The full national subheading varies by country, and export rebate or duty changes affect the final export cost.
Q: Does colour choice affect the PPGI coil price?
Yes. Standard RAL shades produced in long runs are the most economical; white, very light and special-effect colours require more pigment or separate batches and are priced higher.
Q: Do coil weight and coil internal diameter affect the price?
They do. Heavier coils and standard internal diameters of 508 mm or 610 mm run through the line most efficiently. Small coils, unusual internal diameters and special packing all raise the conversion cost per tonne.





