What the 55% Al-Zn Coating Is and How It Is Applied
Hot-dip alu-zinc coated sheet is cold-rolled carbon steel that receives a metallic coating in a continuous hot-dip process. The bath composition is a eutectic-type alloy of approximately 55% aluminium, 43.4% zinc and 1.6% silicon, applied to both surfaces of the strip as it leaves the pot. The silicon addition controls the growth of the brittle aluminium-iron intermetallic layer so that the coating stays adherent during forming. The result is a tough, permanently bonded coating whose behaviour sits between hot-dip zinc and pure aluminium: it provides the barrier protection of an aluminium oxide skin and retains enough zinc to protect sheared edges and scratches galvanically.
The substrate is specified per project. Q355B is a common choice for structural cladding panels because it offers a minimum yield strength of 355 MPa, while Q195 and Q235 are used for lighter profiled sheeting. Cold-rolled substrate with a flat profile is essential, because any shape defect in the base steel is visible through a 20 to 25 µm paint film.
Coating Designations and Sheet Specifications
Coating weight for alu-zinc sheet is quoted as grams per square metre over both surfaces. AZ150, the most widely ordered designation, means 150 g/m² total. EN 10346, ASTM A792 and JIS G3321 all cover the same alloy system, and the designation format is the only significant difference between them.
| Property | Typical range |
|---|---|
| Base steel grade | Q195, Q235, Q345 / Q355B per GB/T 1591 |
| Coating | 55% Al, 43.4% Zn, 1.6% Si |
| Coating weight | AZ100 to AZ185, commonly AZ150 |
| Thickness | 0.13-3.0 mm |
| Width | 600-1500 mm, cut to length on request |
| Paint system | Polyester, silicon-modified polyester, PVDF, 18-25 µm topcoat |
| Standards | EN 10346, ASTM A792, JIS G3321, GB/T 14978 |
Q355B under GB/T 1591 delivers a minimum yield strength of 355 MPa and a tensile range of 470 to 630 MPa with at least 20% elongation at 5.5 mm gauge length for thickness below 16 mm. Impact energy at 20 °C is a minimum of 34 J in the longitudinal direction. Those values matter on long-span purlins and load-bearing wall systems where the panel carries wind or snow load rather than acting purely as a rain screen.
Corrosion and Heat Performance in Service
Alu-zinc coatings outperform conventional zinc coatings in most atmospheric conditions. The aluminium-rich oxide layer forms a stable barrier that resists moisture and industrial pollution, while the zinc phase continues to protect exposed cut edges. Published atmospheric exposure programmes put the time to first red rust for AZ150 material at well over 20 years in rural and urban environments. The coating also reflects radiant heat: alu-zinc surfaces reflect roughly 80% of solar radiation, which lowers roof cavity temperature and reduces thermal movement in long panels compared with bare galvanized steel.
Colour Coating, Fabrication and Handling
Organic coating is applied over a conversion coating and primer on a continuous colour line. Coatings are cured at controlled peak metal temperature so that the film reaches full hardness without embrittling the alloy layer. Recommended practice for fabrication is to keep bend radii at a minimum of two times the sheet thickness for 0.5 mm material and above, to roll-form in the direction of the coil length, and to seal cut edges in aggressive environments. Shearing and punching are straightforward; the exposed aluminium-zinc edge is protected galvanically as long as the coating weight is at least 100 g/m². Protective film should be removed within three months of application to avoid adhesive residue baking onto the paint in strong sunlight.
Quality Control and Supply Format
Incoming strip is checked for coating mass by the gravimetric stripping method, coating adhesion by reverse-impact and T-bend tests, and paint adhesion by cross-hatch and solvent rub. Thickness is measured across the full width to confirm crown and edge drop limits, and the finished coil is inspected for colour consistency against an approved sample under a defined light source. Coils are supplied with an inner diameter of 508 mm or 610 mm and a mill test certificate to EN 10204 3.1 covering both the metallic coating and the organic film. Packing for export uses waterproof kraft paper, plastic film and steel edge protection on non-fumigation pallets, bound with steel strip, which keeps the painted surface free of transit marking on long sea voyages.
Frequently Asked Questions
Q: How does AZ150 compare with a Z275 galvanized coating?
A: Both are quoted at roughly 150 to 275 g/m² total, but the alu-zinc alloy resists atmospheric corrosion longer and reflects heat better, while a pure zinc coating sacrifices itself more readily at cut edges.
Q: Can Q355B alu-zinc sheet be welded on site?
A: Yes, but the coating must be removed from the weld zone first. Aluminium and zinc both vaporise at arc temperature and produce porosity, so the joint is cleaned to bare steel, welded with a matching filler, and the affected area is repaired with a zinc-rich coating.
Q: What paint system is suitable for coastal buildings?
A: A silicon-modified polyester or PVDF topcoat at 23 to 25 µm over a primer of 5 to 7 µm is the usual specification, combined with a coating weight of at least AZ150 to limit undercutting at cut edges and fastener holes.
Q: Does the coating weight affect formability?
A: Heavier coatings are slightly less tolerant of tight radii. For 0.5 mm sheet with AZ150 the practical minimum internal bend radius is about twice the thickness, and lubricant should be used to avoid scoring the paint film.
Q: Which standards apply to an export order?
A: The metallic coating is ordered to EN 10346, ASTM A792 or JIS G3321 and the organic coating to EN 10169, with the base steel to GB/T 1591 or an agreed equivalent. Certificates follow EN 10204 3.1.





