Gnee Steel (tianjin) Co., Ltd
+8615824687445

DX51D DX52D DX53D Z275 Hot-Dip Galvanized Steel Coil: Grades, Coating and Specs

DX51D, DX52D and DX53D are the three most widely ordered cold-forming grades for continuously hot-dip zinc-coated steel coil, and Z275 is the heaviest of the standard coating classes. Together they cover roofing and cladding, appliance housings, ducting and light structural work in which the part is bent, profiled or drawn after coating.

Grade Range: DX51D, DX52D and DX53D Explained

The DX prefix identifies hot-dip coated steel for cold forming under EN 10346, the European standard for continuously hot-dip zinc-coated flat steel products. The number after the letters shows the forming severity the coil is expected to survive, and the final letter shows the coating type, with D standing for hot-dip zinc applied to a cold-rolled base.

DX51D - bending and profiling only; the general-purpose grade used for roofing sheets, wall cladding, ducting and simple panels.

DX52D - drawing grade for moderate forming such as appliance panels and straightforward pressings.

DX53D - deep-drawing grade for severe forming where a lower yield point and higher elongation are required.

DX54D - special deep-drawing grade for the most demanding draws.

Structural grades such as S250GD, S280GD and S350GD belong to the same standard but are ordered against minimum yield strength rather than formability. A structural designation should not be substituted for a DX formability grade on price alone, because the forming behaviour is different even when the coating and dimensions match.

Coating Designations: What Z275 Actually Means

Z275 is a coating mass designation, not a coating thickness. It states that the total mass of zinc on both surfaces is 275 g/m2, which is about 137.5 g/m2 per side and roughly 19 micrometres of zinc on each surface. The standard range runs from about 30 g/m2 for light indoor duty up to 275 g/m2 for the heaviest exterior exposure.

Coating class Total mass, both surfaces Approximate thickness per side Typical duty
Z100 100 g/m2 About 7 micrometres Indoor, dry service
Z180 180 g/m2 About 12.5 micrometres General exterior
Z275 275 g/m2 About 19 micrometres Severe exterior, coastal

Coating mass is the single most important durability variable in the product, because the zinc layer protects the steel both as a barrier and by sacrificial action at cut edges and scratches. Coating designation, base metal thickness and the surface treatment all have to appear on the enquiry, not just the grade name.

Surface Finish and Spangle Options

The appearance of a hot-dip galvanized coil is set by the way the zinc layer solidifies and by the finishing treatment that follows.

Regular spangle - zinc grains grow freely during normal solidification, producing the large visible crystalline pattern traditionally associated with galvanized sheet.

Small spangle - grain growth is restricted so that a finer crystalline pattern is obtained.

Zero spangle - the composition of the bath and a skin-pass after cooling leave a uniform, essentially pattern-free surface.

Zero spangle is usually specified where the coil will be painted or where a uniform appearance matters; regular spangle is common for unpainted roofing and general fabrication. Chromate-free passivation and light oiling are added to control storage stain during transport and short-term storage.

How the Coating Is Applied on a Hot-Dip Line

Production follows a continuous sequence, and control at each step contributes to the final coating quality.

The cold-rolled coil is uncoiled, straightened and welded to the tail of the previous coil so the line runs without stopping.

The strip is cleaned by alkaline spraying, electrolytic degreasing, brushing and rinsing to remove oil, iron particles and residue.

It enters a continuous annealing furnace, where the surface is reduced to a clean, active condition and the required mechanical properties are produced.

The strip passes through the zinc pot at controlled temperature, and the air knife blows off excess liquid zinc to set the coating mass.

Air cooling and water quenching follow, then skin-pass and tension levelling control flatness and surface roughness.

Final steps are chemical passivation, inspection, oiling if specified, and coiling to the ordered coil weight with protective packing.

Typical Mechanical Properties

The values below are the typical windows for the zinc-coated condition under EN 10346; the exact figures depend on thickness and on the producer's own declaration.

Grade Tensile strength Rm (MPa) Elongation A80 (%) Main use
DX51D+Z 270-500 22 minimum Profiling, roofing, cladding
DX52D+Z 270-420 26 minimum Drawing, appliance panels
DX53D+Z 270-380 30 minimum Deep drawing, complex parts

As a rule, the deeper the drawing requirement, the lower the permitted tensile strength and the higher the guaranteed elongation. Upsizing to a deeper drawing grade than the part needs adds cost without benefit, while under-specifying causes cracking at the press.

Coil Dimensions, Packing and Application Notes

Standard supply covers thicknesses of 0.12-2.0 mm and widths of 600-1500 mm, with coil weights of about 3-5 t and coil internal diameters of 508 mm or 610 mm. A minimum order quantity of roughly 25 t corresponds to one 20 ft container load.

Packing normally starts with anti-water paper and three or more strapping strips, and moves up to plastic film with iron-sheet edge protection and pallet fixing for long sea routes. Applications split into three broad groups: construction (roofs, roof structures, rolling doors, rolling shutters, ducting), electrical appliances (refrigerator and washing machine casings, air conditioner parts, stove bodies) and transport (automotive interior panels, back panels and similar components).

Frequently Asked Questions

Q: What does the D at the end of DX51D mean?
In the EN 10346 designation the letter after the forming code identifies the coating, and D denotes hot-dip zinc applied to a cold-rolled base. The complete designation is normally written with the coating mass, for example DX51D+Z275.

Q: What is the difference between DX51D and SGCC?
DX51D is the European designation for a general-purpose cold-forming, hot-dip zinc-coated grade, while SGCC is the equivalent Japanese designation under JIS G3302. They are supplied for similar profiling work, so the declared mechanical properties and coating mass must be compared rather than the grade label alone.

Q: How does Z275 compare with Z120 or Z180?
Z275 carries 275 g/m2 of zinc across both surfaces, against 180 g/m2 for Z180 and 120 g/m2 for Z120. Heavier coating gives longer protection in coastal, industrial and humid service, and it costs more because the zinc is the dominant material cost.

Q: Can DX51D be used instead of DX53D?
Only if the part is formed by bending or light profiling. DX51D has a higher permitted tensile strength and lower guaranteed elongation, so it may crack in deep-drawing operations that DX53D is designed to survive.

Q: Is zero spangle better than regular spangle?
Neither is better in absolute terms. Zero spangle gives a uniform, low-texture surface that suits painting and visible architectural work, while regular spangle offers the traditional crystalline appearance and is widely used for unpainted roofing.

Q: Does a heavier zinc coating always mean a longer service life?
Coating mass is the main durability factor, but service life also depends on the atmosphere, the presence of cut edges, the passivation treatment and correct storage. In highly corrosive environments a heavier coating helps, yet design details and drainage often matter just as much.