What Cold Rolling Does to the Steel
Cold rolled coil starts as hot rolled coil. The hot rolled strip is pickled to remove oxide, then rolled below the recrystallisation temperature, in practice at ambient temperature, so the steel work hardens instead of recrystallising. Rolling at that temperature removes the scale and the surface defects that hot rolling leaves behind, and it produces the flat, bright surface and tight thickness tolerance that give cold rolled product its value. Because the material is not heated, there is no rolled-in oxide, no pitting and no decarburised skin, so surface finish and gauge consistency are markedly better than in hot rolled stock.
Steel with a high silicon content behaves differently in this process: it becomes brittle with low plasticity and usually needs preheating to about 200 °C before rolling, which is a niche route rather than the general case. Standard commercial cold rolling runs on low-carbon aluminium-killed or rimmed steel that deforms predictably at room temperature.
Grades, Standards and Mechanical Ranges
Cold rolled coil is ordered against a grade that fixes the forming severity. EN 10130 covers DC01 through DC07, JIS G3141 covers the SPCC, SPCD and SPCE series, ASTM A1008 covers commercial steel, drawing steel and deep drawing steel, and GB/T 5213 covers the Chinese equivalents.
| Grade | Standard | Yield strength Re, max | Tensile strength Rm | Elongation A80, min |
|---|---|---|---|---|
| DC01 | EN 10130 | 280 MPa | 270-410 MPa | 28% |
| DC03 | EN 10130 | 240 MPa | 270-370 MPa | 34% |
| DC04 | EN 10130 | 210 MPa | 270-350 MPa | 38% |
| SPCC | JIS G3141 | commercial quality | 270 MPa and above | - |
Higher drawing grades add a guaranteed plastic strain ratio r90 and strain hardening exponent n90, which is what allows a panel to be stretched and drawn without localised necking. The work hardening that cold rolling introduces also raises strength and hardness relative to hot rolled material of the same analysis, and it is removed by annealing or controlled by temper rolling to a specified surface roughness and flatness. Temper rolled skin-pass sheet is the normal delivery condition because fully annealed material is prone to stretcher strain marks when formed.
Sizes, Tolerances and Coil Data
Standard production covers thickness from 0.15 mm to 3.0 mm and width from 550 mm to 1530 mm. Coil outside diameter runs from about 1000 mm to 2500 mm with an inside diameter of 410 mm to 610 mm, and maximum coil weight reaches 45 t on heavy-gauge lines. Thickness tolerance is specified to half the normal hot rolled value or better, and flatness, camber and edge condition are inspected against the same standard. The tighter gauge control is what makes cold rolled product suitable for high-speed roll forming and for parts where the assembled thickness stack has to be predictable.
Where Cold Rolled Coil Is Used
Automotive body panels, door inners and structural reinforcements consume large volumes of drawing quality material. Electrical products and appliances use it for enclosures, housings and chassis parts. Rolling stock, aviation ground equipment, precision instruments and food cans rely on the surface finish and formability. Because the surface is clean and flat, cold rolled coil is also the standard substrate for galvanizing, tinplating, colour coating and organic lamination, so a large part of cold rolled output is consumed inside coating lines rather than supplied bare. For each of these uses the delivery condition, the surface roughness and the flatness limit should be agreed in advance, because a coil that meets a commercial roughness range may still fail a class 1 automotive exposed-panel requirement.
Selection, Inspection and Delivery Practice
Specification begins with the forming severity and the surface class, then the gauge, width, temper condition and coil weight. Oiling is standard for transit and forming, either as a rust-preventive oil or as a drawing lubricant, and the oil grade is stated on the certificate. Inspection covers thickness profile across the width, width and camber, flatness, surface roughness Ra, and a visual check for scratches, slivers, roll marks and edge burrs. Mechanical testing reports yield strength, tensile strength, elongation and, for drawing grades, the r and n values from certified tests. Coils are supplied with a mill test certificate to EN 10204 3.1 and are packed with edge protection, waterproof paper and strapping for export shipment.
Frequently Asked Questions
Q: Is cold rolled coil simply hot rolled coil that has been cooled?
A: No. Cold rolling is a separate deformation step carried out below the recrystallisation temperature after pickling, which is what produces the accurate gauge and smooth, scale-free surface.
Q: Why is cold rolled steel stronger but less ductile?
A: Rolling at ambient temperature work hardens the lattice and raises yield and tensile strength, but reduces uniform elongation. Annealing or temper rolling restores the ductility balance required for forming.
Q: What does the temper rolling pass achieve?
A: It applies a light reduction of roughly 0.5% to 1.5% to suppress the yield point elongation that causes stretcher strain marks, and it sets the surface roughness that controls paint appearance and lubricant retention.
Q: What is the maximum coil weight available?
A: Heavy-gauge lines produce coils up to about 45 t, with outside diameters up to 2500 mm and inside diameters of 410 mm to 610 mm. Transport limits at the destination often set the practical maximum.
Q: Can cold rolled coil be supplied without oil?
A: It can, but uncoiled dry material rusts quickly in humid air and is difficult to form without pick-up, so oiling, or a phosphate and oil combination, is the normal delivery condition unless the customer specifies otherwise.





