Surface treatment equipment for high temperature annealing and tension coating of oriented silicon steel
The strip surface treatment equipment mainly includes the following: NO.1 scrubbing tank and NO.1 scrubbing water supply system; sulfuric acid pickling tank, sulfuric acid supply system; hot water spray tank, NO.2 scrubbing tank and NO.2 scrubbing, Spray water supply system; coating liquid supply system.
⑴NO.1 scrubbing tank
Function - This equipment removes magnesium oxide powder and other dirt on the surface of the strip through brushing with the bristles of the brush roller and rinsing with water.
Structure - tank body and tank cover: carbon steel welded steel structure, externally coated with anti-corrosion paint

The main technical parameters:
-Cleaning method: horizontal water brushing, brushing the upper and lower surfaces of the strip five times each;
-Scrubbing water temperature: normal temperature;
-Scrubbing water quality: filtered water;
-Scrubbing water flow: 70m³/h (maximum);
-Scrubbing water pressure: 0.4Mpa (maximum);
-Number of nozzles: 20 (10 at the top and 10 at the bottom); Material: stainless steel (Cr19Ni9);
-Total number of nozzles: 280 (14/nozzle); flat stainless steel nozzles;
- Tank size: about 8.6m (L) × 1.9m (B) × 1.6m (H).
⑵ NO.1 brushing water supply system
Function - This system is located in the basement on the transmission side of the unit. Its function is to supply clean water at normal temperature to the NO.1 scrubbing tank. It consists of tanks, pumps, valves, filters, piping, corresponding detection instruments and control systems.
The main technical parameters:
-NO.1 1 brush water supply tank (10m³); carbon steel;
-NO.1 brushing water pump (1 for use and 1 for backup, Q=70m³/h, H=40m) 2 sets; stainless steel;
-Self-cleaning filter: 1 set; stainless steel;
-Pipes and fittings, expansion joints, valves, gaskets, etc.
Main processes:
After the filtered water in the workshop flows into the NO.1 scrubbing water supply tank, it is pressurized by a pump to supply the NO.1 scrubbing tank to scrub the strip steel. The scrubbed water is discharged to the weak acid wastewater pit as wastewater.
Floor flushing water pipes and safety sprinkler devices are designed on the ground and underground. There is one point on each side of the trough on the ground, and one point on the ground in the middle of the pit.
The floors, ditches, pits, pit walls, and pit roofs in the system pits are all first made of glass phosphorus anti-corrosion layers, and the pits and ditches at a height of half a meter on the floor and pit walls are then made of granite anti-corrosion layers.
⑶ Sulfuric acid pickling tank
Function - This equipment uses sulfuric acid to remove magnesium oxide that has not been removed by the NO.1 scrubbing tank on the surface of the strip steel.
Structure - This equipment is set on the elevated platform of the unit, and the width of the acid tank is about 1.8m. The shell structure of the pickling tank is made of welded steel plates and shaped steel. The tank is lined with acid-resistant rubber plates, acid-resistant bricks and granite (or andesite). The pickling tank is equipped with a tank cover, which is equipped with an acid mist discharge interface. The tank cover is made of carbon steel welded steel structure and is lined with an acid-resistant rubber plate. The tank cover is sealed with acid-resistant rubber. The tank cover is placed in a water-sealed tank lined with acid-resistant rubber sheets and acid-resistant bricks to prevent acid mist from escaping.
The bottom of the pickling tank is made of 12mm thick steel plate, and the side walls are made of 10mm thick steel plate. The inner surface of the finished steel structure of the pickling tank body and tank cover will be lined with two layers of acid-resistant rubber sheets with a total thickness of 6mm (2×3mm=6mm). Before lining with rubber, the surface of the steel structure of the pickling tank must be properly treated to remove the surface oxide scale and make it smooth. The bottom, side and end walls of the tank lined with rubber sheets are lined with one layer of acid-resistant bricks and one layer of granite with furan resin mortar. The outer surface of the steel structure of the pickling tank body and tank cover is coated with multiple layers of acid-resistant and anti-corrosion paint.
The pickling tank is equipped with an acid injection port, an acid return port and an emptying port. During normal production, the acid liquid is sprayed from both sides of the acid tank wall and the bottom of the tank to spray and wash the strip steel in all directions, so that the acid liquid forms a strong turbulent flow state in the tank and enhances the pickling effect.
In order to immerse the strip in the acid solution, immersion rollers are installed at the entrance and exit sides of the pickling tank. The acid temperature is controlled by indirect heating. There are squeezing rollers at the entrance and exit of the acid tank to minimize the amount of acid brought out of the strip. When the operation line is stopped, in order to lift the strip from the acid liquid, a strip lifting device is also installed.
The main technical parameters:
-Immersion roller span: 22000mm;
-Internal dimensions of the acid tank: 24000mm (L) × 1800mm (B) × 700mm (H);
-Pickling medium: sulfuric acid;
-Pickling concentration: 3~15%;
-Pickling temperature: 85±5℃;
-Average height of liquid level: 570mm.







